| FDescription | HAL Function Call |
|---|---|
| Remap SPI1 | __HAL_AFIO_REMAP_SPI1_ENABLE |
| Remap I2C1 | __HAL_AFIO_REMAP_I2C1_ENABLE |
| Remap USART1 | __HAL_AFIO_REMAP_USART1_ENABLE |
| Remap USART2 | __HAL_AFIO_REMAP_USART2_ENABLE |
| Partial Remap USART3 | __HAL_AFIO_REMAP_USART3_PARTIAL |
| Partial Remap TIM1 | __HAL_AFIO_REMAP_TIM1_PARTIAL |
| Partial Remap TIM3 | __HAL_AFIO_REMAP_TIM3_PARTIAL |
| Full Remap TIM2 | __HAL_AFIO_REMAP_TIM2_ENABLE |
| Full Remap TIM3 | __HAL_AFIO_REMAP_TIM3_ENABLE |
| CAN_RX mapped to PB8/CAN_TX mapped to PB9 | __HAL_AFIO_REMAP_CAN1_2 |
/**
******************************************************************************
* @file stm32f1xx_hal_gpio_ex.h
* @author MCD Application Team
* @brief Header file of GPIO HAL Extension module.
******************************************************************************
* @attention
*
* <h2><center>© Copyright (c) 2016 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32F1xx_HAL_GPIO_EX_H
#define STM32F1xx_HAL_GPIO_EX_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32f1xx_hal_def.h"
/** @addtogroup STM32F1xx_HAL_Driver
* @{
*/
/** @defgroup GPIOEx GPIOEx
* @{
*/
/* Exported types ------------------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup GPIOEx_Exported_Constants GPIOEx Exported Constants
* @{
*/
/** @defgroup GPIOEx_EVENTOUT EVENTOUT Cortex Configuration
* @brief This section propose definition to use the Cortex EVENTOUT signal.
* @{
*/
/** @defgroup GPIOEx_EVENTOUT_PIN EVENTOUT Pin
* @{
*/
#define AFIO_EVENTOUT_PIN_0 AFIO_EVCR_PIN_PX0 /*!< EVENTOUT on pin 0 */
#define AFIO_EVENTOUT_PIN_1 AFIO_EVCR_PIN_PX1 /*!< EVENTOUT on pin 1 */
#define AFIO_EVENTOUT_PIN_2 AFIO_EVCR_PIN_PX2 /*!< EVENTOUT on pin 2 */
#define AFIO_EVENTOUT_PIN_3 AFIO_EVCR_PIN_PX3 /*!< EVENTOUT on pin 3 */
#define AFIO_EVENTOUT_PIN_4 AFIO_EVCR_PIN_PX4 /*!< EVENTOUT on pin 4 */
#define AFIO_EVENTOUT_PIN_5 AFIO_EVCR_PIN_PX5 /*!< EVENTOUT on pin 5 */
#define AFIO_EVENTOUT_PIN_6 AFIO_EVCR_PIN_PX6 /*!< EVENTOUT on pin 6 */
#define AFIO_EVENTOUT_PIN_7 AFIO_EVCR_PIN_PX7 /*!< EVENTOUT on pin 7 */
#define AFIO_EVENTOUT_PIN_8 AFIO_EVCR_PIN_PX8 /*!< EVENTOUT on pin 8 */
#define AFIO_EVENTOUT_PIN_9 AFIO_EVCR_PIN_PX9 /*!< EVENTOUT on pin 9 */
#define AFIO_EVENTOUT_PIN_10 AFIO_EVCR_PIN_PX10 /*!< EVENTOUT on pin 10 */
#define AFIO_EVENTOUT_PIN_11 AFIO_EVCR_PIN_PX11 /*!< EVENTOUT on pin 11 */
#define AFIO_EVENTOUT_PIN_12 AFIO_EVCR_PIN_PX12 /*!< EVENTOUT on pin 12 */
#define AFIO_EVENTOUT_PIN_13 AFIO_EVCR_PIN_PX13 /*!< EVENTOUT on pin 13 */
#define AFIO_EVENTOUT_PIN_14 AFIO_EVCR_PIN_PX14 /*!< EVENTOUT on pin 14 */
#define AFIO_EVENTOUT_PIN_15 AFIO_EVCR_PIN_PX15 /*!< EVENTOUT on pin 15 */
#define IS_AFIO_EVENTOUT_PIN(__PIN__) (((__PIN__) == AFIO_EVENTOUT_PIN_0) || \
((__PIN__) == AFIO_EVENTOUT_PIN_1) || \
((__PIN__) == AFIO_EVENTOUT_PIN_2) || \
((__PIN__) == AFIO_EVENTOUT_PIN_3) || \
((__PIN__) == AFIO_EVENTOUT_PIN_4) || \
((__PIN__) == AFIO_EVENTOUT_PIN_5) || \
((__PIN__) == AFIO_EVENTOUT_PIN_6) || \
((__PIN__) == AFIO_EVENTOUT_PIN_7) || \
((__PIN__) == AFIO_EVENTOUT_PIN_8) || \
((__PIN__) == AFIO_EVENTOUT_PIN_9) || \
((__PIN__) == AFIO_EVENTOUT_PIN_10) || \
((__PIN__) == AFIO_EVENTOUT_PIN_11) || \
((__PIN__) == AFIO_EVENTOUT_PIN_12) || \
((__PIN__) == AFIO_EVENTOUT_PIN_13) || \
((__PIN__) == AFIO_EVENTOUT_PIN_14) || \
((__PIN__) == AFIO_EVENTOUT_PIN_15))
/**
* @}
*/
/** @defgroup GPIOEx_EVENTOUT_PORT EVENTOUT Port
* @{
*/
#define AFIO_EVENTOUT_PORT_A AFIO_EVCR_PORT_PA /*!< EVENTOUT on port A */
#define AFIO_EVENTOUT_PORT_B AFIO_EVCR_PORT_PB /*!< EVENTOUT on port B */
#define AFIO_EVENTOUT_PORT_C AFIO_EVCR_PORT_PC /*!< EVENTOUT on port C */
#define AFIO_EVENTOUT_PORT_D AFIO_EVCR_PORT_PD /*!< EVENTOUT on port D */
#define AFIO_EVENTOUT_PORT_E AFIO_EVCR_PORT_PE /*!< EVENTOUT on port E */
#define IS_AFIO_EVENTOUT_PORT(__PORT__) (((__PORT__) == AFIO_EVENTOUT_PORT_A) || \
((__PORT__) == AFIO_EVENTOUT_PORT_B) || \
((__PORT__) == AFIO_EVENTOUT_PORT_C) || \
((__PORT__) == AFIO_EVENTOUT_PORT_D) || \
((__PORT__) == AFIO_EVENTOUT_PORT_E))
/**
* @}
*/
/**
* @}
*/
/** @defgroup GPIOEx_AFIO_AF_REMAPPING Alternate Function Remapping
* @brief This section propose definition to remap the alternate function to some other port/pins.
* @{
*/
/**
* @brief Enable the remapping of SPI1 alternate function NSS, SCK, MISO and MOSI.
* @note ENABLE: Remap (NSS/PA15, SCK/PB3, MISO/PB4, MOSI/PB5)
* @retval None
*/
#define __HAL_AFIO_REMAP_SPI1_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_SPI1_REMAP)
/**
* @brief Disable the remapping of SPI1 alternate function NSS, SCK, MISO and MOSI.
* @note DISABLE: No remap (NSS/PA4, SCK/PA5, MISO/PA6, MOSI/PA7)
* @retval None
*/
#define __HAL_AFIO_REMAP_SPI1_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_SPI1_REMAP)
/**
* @brief Enable the remapping of I2C1 alternate function SCL and SDA.
* @note ENABLE: Remap (SCL/PB8, SDA/PB9)
* @retval None
*/
#define __HAL_AFIO_REMAP_I2C1_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_I2C1_REMAP)
/**
* @brief Disable the remapping of I2C1 alternate function SCL and SDA.
* @note DISABLE: No remap (SCL/PB6, SDA/PB7)
* @retval None
*/
#define __HAL_AFIO_REMAP_I2C1_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_I2C1_REMAP)
/**
* @brief Enable the remapping of USART1 alternate function TX and RX.
* @note ENABLE: Remap (TX/PB6, RX/PB7)
* @retval None
*/
#define __HAL_AFIO_REMAP_USART1_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_USART1_REMAP)
/**
* @brief Disable the remapping of USART1 alternate function TX and RX.
* @note DISABLE: No remap (TX/PA9, RX/PA10)
* @retval None
*/
#define __HAL_AFIO_REMAP_USART1_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_USART1_REMAP)
/**
* @brief Enable the remapping of USART2 alternate function CTS, RTS, CK, TX and RX.
* @note ENABLE: Remap (CTS/PD3, RTS/PD4, TX/PD5, RX/PD6, CK/PD7)
* @retval None
*/
#define __HAL_AFIO_REMAP_USART2_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_USART2_REMAP)
/**
* @brief Disable the remapping of USART2 alternate function CTS, RTS, CK, TX and RX.
* @note DISABLE: No remap (CTS/PA0, RTS/PA1, TX/PA2, RX/PA3, CK/PA4)
* @retval None
*/
#define __HAL_AFIO_REMAP_USART2_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_USART2_REMAP)
/**
* @brief Enable the remapping of USART3 alternate function CTS, RTS, CK, TX and RX.
* @note ENABLE: Full remap (TX/PD8, RX/PD9, CK/PD10, CTS/PD11, RTS/PD12)
* @retval None
*/
#define __HAL_AFIO_REMAP_USART3_ENABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_USART3_REMAP_FULLREMAP, AFIO_MAPR_USART3_REMAP_FULLREMAP)
/**
* @brief Enable the remapping of USART3 alternate function CTS, RTS, CK, TX and RX.
* @note PARTIAL: Partial remap (TX/PC10, RX/PC11, CK/PC12, CTS/PB13, RTS/PB14)
* @retval None
*/
#define __HAL_AFIO_REMAP_USART3_PARTIAL() AFIO_REMAP_PARTIAL(AFIO_MAPR_USART3_REMAP_PARTIALREMAP, AFIO_MAPR_USART3_REMAP_FULLREMAP)
/**
* @brief Disable the remapping of USART3 alternate function CTS, RTS, CK, TX and RX.
* @note DISABLE: No remap (TX/PB10, RX/PB11, CK/PB12, CTS/PB13, RTS/PB14)
* @retval None
*/
#define __HAL_AFIO_REMAP_USART3_DISABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_USART3_REMAP_NOREMAP, AFIO_MAPR_USART3_REMAP_FULLREMAP)
/**
* @brief Enable the remapping of TIM1 alternate function channels 1 to 4, 1N to 3N, external trigger (ETR) and Break input (BKIN)
* @note ENABLE: Full remap (ETR/PE7, CH1/PE9, CH2/PE11, CH3/PE13, CH4/PE14, BKIN/PE15, CH1N/PE8, CH2N/PE10, CH3N/PE12)
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM1_ENABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM1_REMAP_FULLREMAP, AFIO_MAPR_TIM1_REMAP_FULLREMAP)
/**
* @brief Enable the remapping of TIM1 alternate function channels 1 to 4, 1N to 3N, external trigger (ETR) and Break input (BKIN)
* @note PARTIAL: Partial remap (ETR/PA12, CH1/PA8, CH2/PA9, CH3/PA10, CH4/PA11, BKIN/PA6, CH1N/PA7, CH2N/PB0, CH3N/PB1)
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM1_PARTIAL() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM1_REMAP_PARTIALREMAP, AFIO_MAPR_TIM1_REMAP_FULLREMAP)
/**
* @brief Disable the remapping of TIM1 alternate function channels 1 to 4, 1N to 3N, external trigger (ETR) and Break input (BKIN)
* @note DISABLE: No remap (ETR/PA12, CH1/PA8, CH2/PA9, CH3/PA10, CH4/PA11, BKIN/PB12, CH1N/PB13, CH2N/PB14, CH3N/PB15)
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM1_DISABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM1_REMAP_NOREMAP, AFIO_MAPR_TIM1_REMAP_FULLREMAP)
/**
* @brief Enable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR)
* @note ENABLE: Full remap (CH1/ETR/PA15, CH2/PB3, CH3/PB10, CH4/PB11)
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM2_ENABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM2_REMAP_FULLREMAP, AFIO_MAPR_TIM2_REMAP_FULLREMAP)
/**
* @brief Enable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR)
* @note PARTIAL_2: Partial remap (CH1/ETR/PA0, CH2/PA1, CH3/PB10, CH4/PB11)
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM2_PARTIAL_2() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM2_REMAP_PARTIALREMAP2, AFIO_MAPR_TIM2_REMAP_FULLREMAP)
/**
* @brief Enable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR)
* @note PARTIAL_1: Partial remap (CH1/ETR/PA15, CH2/PB3, CH3/PA2, CH4/PA3)
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM2_PARTIAL_1() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM2_REMAP_PARTIALREMAP1, AFIO_MAPR_TIM2_REMAP_FULLREMAP)
/**
* @brief Disable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR)
* @note DISABLE: No remap (CH1/ETR/PA0, CH2/PA1, CH3/PA2, CH4/PA3)
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM2_DISABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM2_REMAP_NOREMAP, AFIO_MAPR_TIM2_REMAP_FULLREMAP)
/**
* @brief Enable the remapping of TIM3 alternate function channels 1 to 4
* @note ENABLE: Full remap (CH1/PC6, CH2/PC7, CH3/PC8, CH4/PC9)
* @note TIM3_ETR on PE0 is not re-mapped.
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM3_ENABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM3_REMAP_FULLREMAP, AFIO_MAPR_TIM3_REMAP_FULLREMAP)
/**
* @brief Enable the remapping of TIM3 alternate function channels 1 to 4
* @note PARTIAL: Partial remap (CH1/PB4, CH2/PB5, CH3/PB0, CH4/PB1)
* @note TIM3_ETR on PE0 is not re-mapped.
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM3_PARTIAL() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM3_REMAP_PARTIALREMAP, AFIO_MAPR_TIM3_REMAP_FULLREMAP)
/**
* @brief Disable the remapping of TIM3 alternate function channels 1 to 4
* @note DISABLE: No remap (CH1/PA6, CH2/PA7, CH3/PB0, CH4/PB1)
* @note TIM3_ETR on PE0 is not re-mapped.
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM3_DISABLE() AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM3_REMAP_NOREMAP, AFIO_MAPR_TIM3_REMAP_FULLREMAP)
/**
* @brief Enable the remapping of TIM4 alternate function channels 1 to 4.
* @note ENABLE: Full remap (TIM4_CH1/PD12, TIM4_CH2/PD13, TIM4_CH3/PD14, TIM4_CH4/PD15)
* @note TIM4_ETR on PE0 is not re-mapped.
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM4_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_TIM4_REMAP)
/**
* @brief Disable the remapping of TIM4 alternate function channels 1 to 4.
* @note DISABLE: No remap (TIM4_CH1/PB6, TIM4_CH2/PB7, TIM4_CH3/PB8, TIM4_CH4/PB9)
* @note TIM4_ETR on PE0 is not re-mapped.
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM4_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_TIM4_REMAP)
#if defined(AFIO_MAPR_CAN_REMAP_REMAP1)
/**
* @brief Enable or disable the remapping of CAN alternate function CAN_RX and CAN_TX in devices with a single CAN interface.
* @note CASE 1: CAN_RX mapped to PA11, CAN_TX mapped to PA12
* @retval None
*/
#define __HAL_AFIO_REMAP_CAN1_1() AFIO_REMAP_PARTIAL(AFIO_MAPR_CAN_REMAP_REMAP1, AFIO_MAPR_CAN_REMAP)
/**
* @brief Enable or disable the remapping of CAN alternate function CAN_RX and CAN_TX in devices with a single CAN interface.
* @note CASE 2: CAN_RX mapped to PB8, CAN_TX mapped to PB9 (not available on 36-pin package)
* @retval None
*/
#define __HAL_AFIO_REMAP_CAN1_2() AFIO_REMAP_PARTIAL(AFIO_MAPR_CAN_REMAP_REMAP2, AFIO_MAPR_CAN_REMAP)
/**
* @brief Enable or disable the remapping of CAN alternate function CAN_RX and CAN_TX in devices with a single CAN interface.
* @note CASE 3: CAN_RX mapped to PD0, CAN_TX mapped to PD1
* @retval None
*/
#define __HAL_AFIO_REMAP_CAN1_3() AFIO_REMAP_PARTIAL(AFIO_MAPR_CAN_REMAP_REMAP3, AFIO_MAPR_CAN_REMAP)
#endif
/**
* @brief Enable the remapping of PD0 and PD1. When the HSE oscillator is not used
* (application running on internal 8 MHz RC) PD0 and PD1 can be mapped on OSC_IN and
* OSC_OUT. This is available only on 36, 48 and 64 pins packages (PD0 and PD1 are available
* on 100-pin and 144-pin packages, no need for remapping).
* @note ENABLE: PD0 remapped on OSC_IN, PD1 remapped on OSC_OUT.
* @retval None
*/
#define __HAL_AFIO_REMAP_PD01_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_PD01_REMAP)
/**
* @brief Disable the remapping of PD0 and PD1. When the HSE oscillator is not used
* (application running on internal 8 MHz RC) PD0 and PD1 can be mapped on OSC_IN and
* OSC_OUT. This is available only on 36, 48 and 64 pins packages (PD0 and PD1 are available
* on 100-pin and 144-pin packages, no need for remapping).
* @note DISABLE: No remapping of PD0 and PD1
* @retval None
*/
#define __HAL_AFIO_REMAP_PD01_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_PD01_REMAP)
#if defined(AFIO_MAPR_TIM5CH4_IREMAP)
/**
* @brief Enable the remapping of TIM5CH4.
* @note ENABLE: LSI internal clock is connected to TIM5_CH4 input for calibration purpose.
* @note This function is available only in high density value line devices.
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM5CH4_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_TIM5CH4_IREMAP)
/**
* @brief Disable the remapping of TIM5CH4.
* @note DISABLE: TIM5_CH4 is connected to PA3
* @note This function is available only in high density value line devices.
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM5CH4_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_TIM5CH4_IREMAP)
#endif
#if defined(AFIO_MAPR_ETH_REMAP)
/**
* @brief Enable the remapping of Ethernet MAC connections with the PHY.
* @note ENABLE: Remap (RX_DV-CRS_DV/PD8, RXD0/PD9, RXD1/PD10, RXD2/PD11, RXD3/PD12)
* @note This bit is available only in connectivity line devices and is reserved otherwise.
* @retval None
*/
#define __HAL_AFIO_REMAP_ETH_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_ETH_REMAP)
/**
* @brief Disable the remapping of Ethernet MAC connections with the PHY.
* @note DISABLE: No remap (RX_DV-CRS_DV/PA7, RXD0/PC4, RXD1/PC5, RXD2/PB0, RXD3/PB1)
* @note This bit is available only in connectivity line devices and is reserved otherwise.
* @retval None
*/
#define __HAL_AFIO_REMAP_ETH_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ETH_REMAP)
#endif
#if defined(AFIO_MAPR_CAN2_REMAP)
/**
* @brief Enable the remapping of CAN2 alternate function CAN2_RX and CAN2_TX.
* @note ENABLE: Remap (CAN2_RX/PB5, CAN2_TX/PB6)
* @note This bit is available only in connectivity line devices and is reserved otherwise.
* @retval None
*/
#define __HAL_AFIO_REMAP_CAN2_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_CAN2_REMAP)
/**
* @brief Disable the remapping of CAN2 alternate function CAN2_RX and CAN2_TX.
* @note DISABLE: No remap (CAN2_RX/PB12, CAN2_TX/PB13)
* @note This bit is available only in connectivity line devices and is reserved otherwise.
* @retval None
*/
#define __HAL_AFIO_REMAP_CAN2_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_CAN2_REMAP)
#endif
#if defined(AFIO_MAPR_MII_RMII_SEL)
/**
* @brief Configures the Ethernet MAC internally for use with an external MII or RMII PHY.
* @note ETH_RMII: Configure Ethernet MAC for connection with an RMII PHY
* @note This bit is available only in connectivity line devices and is reserved otherwise.
* @retval None
*/
#define __HAL_AFIO_ETH_RMII() AFIO_REMAP_ENABLE(AFIO_MAPR_MII_RMII_SEL)
/**
* @brief Configures the Ethernet MAC internally for use with an external MII or RMII PHY.
* @note ETH_MII: Configure Ethernet MAC for connection with an MII PHY
* @note This bit is available only in connectivity line devices and is reserved otherwise.
* @retval None
*/
#define __HAL_AFIO_ETH_MII() AFIO_REMAP_DISABLE(AFIO_MAPR_MII_RMII_SEL)
#endif
/**
* @brief Enable the remapping of ADC1_ETRGINJ (ADC 1 External trigger injected conversion).
* @note ENABLE: ADC1 External Event injected conversion is connected to TIM8 Channel4.
* @retval None
*/
#define __HAL_AFIO_REMAP_ADC1_ETRGINJ_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_ADC1_ETRGINJ_REMAP)
/**
* @brief Disable the remapping of ADC1_ETRGINJ (ADC 1 External trigger injected conversion).
* @note DISABLE: ADC1 External trigger injected conversion is connected to EXTI15
* @retval None
*/
#define __HAL_AFIO_REMAP_ADC1_ETRGINJ_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ADC1_ETRGINJ_REMAP)
/**
* @brief Enable the remapping of ADC1_ETRGREG (ADC 1 External trigger regular conversion).
* @note ENABLE: ADC1 External Event regular conversion is connected to TIM8 TRG0.
* @retval None
*/
#define __HAL_AFIO_REMAP_ADC1_ETRGREG_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_ADC1_ETRGREG_REMAP)
/**
* @brief Disable the remapping of ADC1_ETRGREG (ADC 1 External trigger regular conversion).
* @note DISABLE: ADC1 External trigger regular conversion is connected to EXTI11
* @retval None
*/
#define __HAL_AFIO_REMAP_ADC1_ETRGREG_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ADC1_ETRGREG_REMAP)
#if defined(AFIO_MAPR_ADC2_ETRGINJ_REMAP)
/**
* @brief Enable the remapping of ADC2_ETRGREG (ADC 2 External trigger injected conversion).
* @note ENABLE: ADC2 External Event injected conversion is connected to TIM8 Channel4.
* @retval None
*/
#define __HAL_AFIO_REMAP_ADC2_ETRGINJ_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_ADC2_ETRGINJ_REMAP)
/**
* @brief Disable the remapping of ADC2_ETRGREG (ADC 2 External trigger injected conversion).
* @note DISABLE: ADC2 External trigger injected conversion is connected to EXTI15
* @retval None
*/
#define __HAL_AFIO_REMAP_ADC2_ETRGINJ_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ADC2_ETRGINJ_REMAP)
#endif
#if defined (AFIO_MAPR_ADC2_ETRGREG_REMAP)
/**
* @brief Enable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion).
* @note ENABLE: ADC2 External Event regular conversion is connected to TIM8 TRG0.
* @retval None
*/
#define __HAL_AFIO_REMAP_ADC2_ETRGREG_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_ADC2_ETRGREG_REMAP)
/**
* @brief Disable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion).
* @note DISABLE: ADC2 External trigger regular conversion is connected to EXTI11
* @retval None
*/
#define __HAL_AFIO_REMAP_ADC2_ETRGREG_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ADC2_ETRGREG_REMAP)
#endif
/**
* @brief Enable the Serial wire JTAG configuration
* @note ENABLE: Full SWJ (JTAG-DP + SW-DP): Reset State
* @retval None
*/
#define __HAL_AFIO_REMAP_SWJ_ENABLE() AFIO_DBGAFR_CONFIG(AFIO_MAPR_SWJ_CFG_RESET)
/**
* @brief Enable the Serial wire JTAG configuration
* @note NONJTRST: Full SWJ (JTAG-DP + SW-DP) but without NJTRST
* @retval None
*/
#define __HAL_AFIO_REMAP_SWJ_NONJTRST() AFIO_DBGAFR_CONFIG(AFIO_MAPR_SWJ_CFG_NOJNTRST)
/**
* @brief Enable the Serial wire JTAG configuration
* @note NOJTAG: JTAG-DP Disabled and SW-DP Enabled
* @retval None
*/
#define __HAL_AFIO_REMAP_SWJ_NOJTAG() AFIO_DBGAFR_CONFIG(AFIO_MAPR_SWJ_CFG_JTAGDISABLE)
/**
* @brief Disable the Serial wire JTAG configuration
* @note DISABLE: JTAG-DP Disabled and SW-DP Disabled
* @retval None
*/
#define __HAL_AFIO_REMAP_SWJ_DISABLE() AFIO_DBGAFR_CONFIG(AFIO_MAPR_SWJ_CFG_DISABLE)
#if defined(AFIO_MAPR_SPI3_REMAP)
/**
* @brief Enable the remapping of SPI3 alternate functions SPI3_NSS/I2S3_WS, SPI3_SCK/I2S3_CK, SPI3_MISO, SPI3_MOSI/I2S3_SD.
* @note ENABLE: Remap (SPI3_NSS-I2S3_WS/PA4, SPI3_SCK-I2S3_CK/PC10, SPI3_MISO/PC11, SPI3_MOSI-I2S3_SD/PC12)
* @note This bit is available only in connectivity line devices and is reserved otherwise.
* @retval None
*/
#define __HAL_AFIO_REMAP_SPI3_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_SPI3_REMAP)
/**
* @brief Disable the remapping of SPI3 alternate functions SPI3_NSS/I2S3_WS, SPI3_SCK/I2S3_CK, SPI3_MISO, SPI3_MOSI/I2S3_SD.
* @note DISABLE: No remap (SPI3_NSS-I2S3_WS/PA15, SPI3_SCK-I2S3_CK/PB3, SPI3_MISO/PB4, SPI3_MOSI-I2S3_SD/PB5).
* @note This bit is available only in connectivity line devices and is reserved otherwise.
* @retval None
*/
#define __HAL_AFIO_REMAP_SPI3_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_SPI3_REMAP)
#endif
#if defined(AFIO_MAPR_TIM2ITR1_IREMAP)
/**
* @brief Control of TIM2_ITR1 internal mapping.
* @note TO_USB: Connect USB OTG SOF (Start of Frame) output to TIM2_ITR1 for calibration purposes.
* @note This bit is available only in connectivity line devices and is reserved otherwise.
* @retval None
*/
#define __HAL_AFIO_TIM2ITR1_TO_USB() AFIO_REMAP_ENABLE(AFIO_MAPR_TIM2ITR1_IREMAP)
/**
* @brief Control of TIM2_ITR1 internal mapping.
* @note TO_ETH: Connect TIM2_ITR1 internally to the Ethernet PTP output for calibration purposes.
* @note This bit is available only in connectivity line devices and is reserved otherwise.
* @retval None
*/
#define __HAL_AFIO_TIM2ITR1_TO_ETH() AFIO_REMAP_DISABLE(AFIO_MAPR_TIM2ITR1_IREMAP)
#endif
#if defined(AFIO_MAPR_PTP_PPS_REMAP)
/**
* @brief Enable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion).
* @note ENABLE: PTP_PPS is output on PB5 pin.
* @note This bit is available only in connectivity line devices and is reserved otherwise.
* @retval None
*/
#define __HAL_AFIO_ETH_PTP_PPS_ENABLE() AFIO_REMAP_ENABLE(AFIO_MAPR_PTP_PPS_REMAP)
/**
* @brief Disable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion).
* @note DISABLE: PTP_PPS not output on PB5 pin.
* @note This bit is available only in connectivity line devices and is reserved otherwise.
* @retval None
*/
#define __HAL_AFIO_ETH_PTP_PPS_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_PTP_PPS_REMAP)
#endif
#if defined(AFIO_MAPR2_TIM9_REMAP)
/**
* @brief Enable the remapping of TIM9_CH1 and TIM9_CH2.
* @note ENABLE: Remap (TIM9_CH1 on PE5 and TIM9_CH2 on PE6).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM9_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM9_REMAP)
/**
* @brief Disable the remapping of TIM9_CH1 and TIM9_CH2.
* @note DISABLE: No remap (TIM9_CH1 on PA2 and TIM9_CH2 on PA3).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM9_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM9_REMAP)
#endif
#if defined(AFIO_MAPR2_TIM10_REMAP)
/**
* @brief Enable the remapping of TIM10_CH1.
* @note ENABLE: Remap (TIM10_CH1 on PF6).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM10_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM10_REMAP)
/**
* @brief Disable the remapping of TIM10_CH1.
* @note DISABLE: No remap (TIM10_CH1 on PB8).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM10_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM10_REMAP)
#endif
#if defined(AFIO_MAPR2_TIM11_REMAP)
/**
* @brief Enable the remapping of TIM11_CH1.
* @note ENABLE: Remap (TIM11_CH1 on PF7).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM11_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM11_REMAP)
/**
* @brief Disable the remapping of TIM11_CH1.
* @note DISABLE: No remap (TIM11_CH1 on PB9).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM11_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM11_REMAP)
#endif
#if defined(AFIO_MAPR2_TIM13_REMAP)
/**
* @brief Enable the remapping of TIM13_CH1.
* @note ENABLE: Remap STM32F100:(TIM13_CH1 on PF8). Others:(TIM13_CH1 on PB0).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM13_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM13_REMAP)
/**
* @brief Disable the remapping of TIM13_CH1.
* @note DISABLE: No remap STM32F100:(TIM13_CH1 on PA6). Others:(TIM13_CH1 on PC8).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM13_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM13_REMAP)
#endif
#if defined(AFIO_MAPR2_TIM14_REMAP)
/**
* @brief Enable the remapping of TIM14_CH1.
* @note ENABLE: Remap STM32F100:(TIM14_CH1 on PB1). Others:(TIM14_CH1 on PF9).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM14_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM14_REMAP)
/**
* @brief Disable the remapping of TIM14_CH1.
* @note DISABLE: No remap STM32F100:(TIM14_CH1 on PC9). Others:(TIM14_CH1 on PA7).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM14_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM14_REMAP)
#endif
#if defined(AFIO_MAPR2_FSMC_NADV_REMAP)
/**
* @brief Controls the use of the optional FSMC_NADV signal.
* @note DISCONNECTED: The NADV signal is not connected. The I/O pin can be used by another peripheral.
* @retval None
*/
#define __HAL_AFIO_FSMCNADV_DISCONNECTED() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_FSMC_NADV_REMAP)
/**
* @brief Controls the use of the optional FSMC_NADV signal.
* @note CONNECTED: The NADV signal is connected to the output (default).
* @retval None
*/
#define __HAL_AFIO_FSMCNADV_CONNECTED() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_FSMC_NADV_REMAP)
#endif
#if defined(AFIO_MAPR2_TIM15_REMAP)
/**
* @brief Enable the remapping of TIM15_CH1 and TIM15_CH2.
* @note ENABLE: Remap (TIM15_CH1 on PB14 and TIM15_CH2 on PB15).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM15_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM15_REMAP)
/**
* @brief Disable the remapping of TIM15_CH1 and TIM15_CH2.
* @note DISABLE: No remap (TIM15_CH1 on PA2 and TIM15_CH2 on PA3).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM15_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM15_REMAP)
#endif
#if defined(AFIO_MAPR2_TIM16_REMAP)
/**
* @brief Enable the remapping of TIM16_CH1.
* @note ENABLE: Remap (TIM16_CH1 on PA6).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM16_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM16_REMAP)
/**
* @brief Disable the remapping of TIM16_CH1.
* @note DISABLE: No remap (TIM16_CH1 on PB8).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM16_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM16_REMAP)
#endif
#if defined(AFIO_MAPR2_TIM17_REMAP)
/**
* @brief Enable the remapping of TIM17_CH1.
* @note ENABLE: Remap (TIM17_CH1 on PA7).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM17_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM17_REMAP)
/**
* @brief Disable the remapping of TIM17_CH1.
* @note DISABLE: No remap (TIM17_CH1 on PB9).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM17_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM17_REMAP)
#endif
#if defined(AFIO_MAPR2_CEC_REMAP)
/**
* @brief Enable the remapping of CEC.
* @note ENABLE: Remap (CEC on PB10).
* @retval None
*/
#define __HAL_AFIO_REMAP_CEC_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_CEC_REMAP)
/**
* @brief Disable the remapping of CEC.
* @note DISABLE: No remap (CEC on PB8).
* @retval None
*/
#define __HAL_AFIO_REMAP_CEC_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_CEC_REMAP)
#endif
#if defined(AFIO_MAPR2_TIM1_DMA_REMAP)
/**
* @brief Controls the mapping of the TIM1_CH1 TIM1_CH2 DMA requests onto the DMA1 channels.
* @note ENABLE: Remap (TIM1_CH1 DMA request/DMA1 Channel6, TIM1_CH2 DMA request/DMA1 Channel6)
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM1DMA_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM1_DMA_REMAP)
/**
* @brief Controls the mapping of the TIM1_CH1 TIM1_CH2 DMA requests onto the DMA1 channels.
* @note DISABLE: No remap (TIM1_CH1 DMA request/DMA1 Channel2, TIM1_CH2 DMA request/DMA1 Channel3).
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM1DMA_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM1_DMA_REMAP)
#endif
#if defined(AFIO_MAPR2_TIM67_DAC_DMA_REMAP)
/**
* @brief Controls the mapping of the TIM6_DAC1 and TIM7_DAC2 DMA requests onto the DMA1 channels.
* @note ENABLE: Remap (TIM6_DAC1 DMA request/DMA1 Channel3, TIM7_DAC2 DMA request/DMA1 Channel4)
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM67DACDMA_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM67_DAC_DMA_REMAP)
/**
* @brief Controls the mapping of the TIM6_DAC1 and TIM7_DAC2 DMA requests onto the DMA1 channels.
* @note DISABLE: No remap (TIM6_DAC1 DMA request/DMA2 Channel3, TIM7_DAC2 DMA request/DMA2 Channel4)
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM67DACDMA_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM67_DAC_DMA_REMAP)
#endif
#if defined(AFIO_MAPR2_TIM12_REMAP)
/**
* @brief Enable the remapping of TIM12_CH1 and TIM12_CH2.
* @note ENABLE: Remap (TIM12_CH1 on PB12 and TIM12_CH2 on PB13).
* @note This bit is available only in high density value line devices.
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM12_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM12_REMAP)
/**
* @brief Disable the remapping of TIM12_CH1 and TIM12_CH2.
* @note DISABLE: No remap (TIM12_CH1 on PC4 and TIM12_CH2 on PC5).
* @note This bit is available only in high density value line devices.
* @retval None
*/
#define __HAL_AFIO_REMAP_TIM12_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM12_REMAP)
#endif
#if defined(AFIO_MAPR2_MISC_REMAP)
/**
* @brief Miscellaneous features remapping.
* This bit is set and cleared by software. It controls miscellaneous features.
* The DMA2 channel 5 interrupt position in the vector table.
* The timer selection for DAC trigger 3 (TSEL[2:0] = 011, for more details refer to the DAC_CR register).
* @note ENABLE: DMA2 channel 5 interrupt is mapped separately at position 60 and TIM15 TRGO event is
* selected as DAC Trigger 3, TIM15 triggers TIM1/3.
* @note This bit is available only in high density value line devices.
* @retval None
*/
#define __HAL_AFIO_REMAP_MISC_ENABLE() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_MISC_REMAP)
/**
* @brief Miscellaneous features remapping.
* This bit is set and cleared by software. It controls miscellaneous features.
* The DMA2 channel 5 interrupt position in the vector table.
* The timer selection for DAC trigger 3 (TSEL[2:0] = 011, for more details refer to the DAC_CR register).
* @note DISABLE: DMA2 channel 5 interrupt is mapped with DMA2 channel 4 at position 59, TIM5 TRGO
* event is selected as DAC Trigger 3, TIM5 triggers TIM1/3.
* @note This bit is available only in high density value line devices.
* @retval None
*/
#define __HAL_AFIO_REMAP_MISC_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_MISC_REMAP)
#endif
/**
* @}
*/
/**
* @}
*/
/** @defgroup GPIOEx_Private_Macros GPIOEx Private Macros
* @{
*/
#if defined(STM32F101x6) || defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6)
#define GPIO_GET_INDEX(__GPIOx__) (((__GPIOx__) == (GPIOA))? 0uL :\
((__GPIOx__) == (GPIOB))? 1uL :\
((__GPIOx__) == (GPIOC))? 2uL :3uL)
#elif defined(STM32F100xB) || defined(STM32F101xB) || defined(STM32F103xB) || defined(STM32F105xC) || defined(STM32F107xC)
#define GPIO_GET_INDEX(__GPIOx__) (((__GPIOx__) == (GPIOA))? 0uL :\
((__GPIOx__) == (GPIOB))? 1uL :\
((__GPIOx__) == (GPIOC))? 2uL :\
((__GPIOx__) == (GPIOD))? 3uL :4uL)
#elif defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG)
#define GPIO_GET_INDEX(__GPIOx__) (((__GPIOx__) == (GPIOA))? 0uL :\
((__GPIOx__) == (GPIOB))? 1uL :\
((__GPIOx__) == (GPIOC))? 2uL :\
((__GPIOx__) == (GPIOD))? 3uL :\
((__GPIOx__) == (GPIOE))? 4uL :\
((__GPIOx__) == (GPIOF))? 5uL :6uL)
#endif
#define AFIO_REMAP_ENABLE(REMAP_PIN) do{ uint32_t tmpreg = AFIO->MAPR; \
tmpreg |= AFIO_MAPR_SWJ_CFG; \
tmpreg |= REMAP_PIN; \
AFIO->MAPR = tmpreg; \
}while(0u)
#define AFIO_REMAP_DISABLE(REMAP_PIN) do{ uint32_t tmpreg = AFIO->MAPR; \
tmpreg |= AFIO_MAPR_SWJ_CFG; \
tmpreg &= ~REMAP_PIN; \
AFIO->MAPR = tmpreg; \
}while(0u)
#define AFIO_REMAP_PARTIAL(REMAP_PIN, REMAP_PIN_MASK) do{ uint32_t tmpreg = AFIO->MAPR; \
tmpreg &= ~REMAP_PIN_MASK; \
tmpreg |= AFIO_MAPR_SWJ_CFG; \
tmpreg |= REMAP_PIN; \
AFIO->MAPR = tmpreg; \
}while(0u)
#define AFIO_DBGAFR_CONFIG(DBGAFR_SWJCFG) do{ uint32_t tmpreg = AFIO->MAPR; \
tmpreg &= ~AFIO_MAPR_SWJ_CFG_Msk; \
tmpreg |= DBGAFR_SWJCFG; \
AFIO->MAPR = tmpreg; \
}while(0u)
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/* Exported functions --------------------------------------------------------*/
/** @addtogroup GPIOEx_Exported_Functions
* @{
*/
/** @addtogroup GPIOEx_Exported_Functions_Group1
* @{
*/
void HAL_GPIOEx_ConfigEventout(uint32_t GPIO_PortSource, uint32_t GPIO_PinSource);
void HAL_GPIOEx_EnableEventout(void);
void HAL_GPIOEx_DisableEventout(void);
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* STM32F1xx_HAL_GPIO_EX_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/